Sensor Head for CMD/HMD Sensor Head and Fiber Unit for CMD/HMD Nhận báo giá
MBX-211 MBX-211 Nhận báo giá

LAV

Nhận báo giá

High performance design with using semiconductor laser

LAV
LAV
Nhận báo giá

Giá trên website là giá bán lẻ, liên hệ để có giá tốt nhất !!!

LAV

Overview

-> This is an optical fiber type CMD using semi-conductor laser as light source. This equipment is composed of transmitter(Sensor head, heat-resistance fiber and amplifier) and receiver and detects steel material which passes through between them. It emits more powerfully compared with LED type so that high performance with margin in bad environment is possible.
-> This doesn’t specify power source. It is capable of being used within the scope of 100 to 240VAC.
-> Water-cooling or air-purge isn’t required for sensor head because non-air dust purge hood is applied.
-> 8-point LED display unable to monitor the margin and emitting state.
-> This is safe design because laser beam doesn’t emit if fiber is not connected.
-> Warning output is provided.

Specifications

Specifications

Model No.Amplifier : Basic type LAV-10P/Strong power type LAV-11P(Projector), LAV-10A(Receiver)
Sensor head : FHM-211-1 or FHM-311
Fiber unit*1 : FHV-321(2m), FHV-351(5m), FHV-411(10m)
Safety standardClass 1(JIS C6802)
Detectable objectsSteel material with φ100mm or more(FHM-311)
Detecting distance50m(Detection margin : 10,000 times or more at 10m*2)
Power source100 to 240VAC(+10%, – 15%, 50/60Hz)
Power consumptionProjector : 5VA or less, Receiver : 5.5VA or less
Control output1C relay contact(250VAC 3A, 30VDC 5A, COSφ=1),
Photo-coupler(120V, 100mA)
Warning output
Light-emitting amount Lowering output
Analog voltage outputDC voltage output in proportion to light-receiving amount(Saturated value 9V or more but do not use it except for adjustment)
Response timeContact output : 40msec or less, transistor output : 30msec or less
Operating modeChangeover of DARK-ON/LIGHT-ON
ConnectionConnector type(Cable 2m)
Fiber unit characteristicsAllowable bending radius : 100mm, Max. pressure : 784MPa, Tension strength : 490N
Ambient illuminanceIncandescent lamp : 10,000lux
Ambient temperatureAmplifier : -10 to +55°, Sensor head/Fiber unit : -10 to +200°
Ambient humidity45 to 85%RH(Not frozen)
Insulation resistance20MΩ or more(1,000V megger between power/output contact and case)
Withstand voltage1,500VAC/min. (Between power/output contact and case)
Vibration resistance10 to 55Hz Double amplitude 1.5mm Each 2 hour in X, Y and Z directions
Impact resistance490m/s2, Each 3 time in X, Y and Z directions
Protective structureAmplifier : IP64(IEC standard)
Sensor head : IP66(IEC standard)
Fiber unit : Corrugated tube with blade(SUS)
CaseAmplifier : Aluminum die-casting, Sensor head : Aluminum
WeightAmplifier : Approx. 950g
Sensor head : FHM-211-1 approx. 1.5kg, FHM-311 approx. 4.0kg,
Fiber unit : FHV-321 approx. 1.0kg, FHV-351 approx. 1.8kg, FHV-411 approx. 2.8kg

*1 3m, 15m and 20m type are also available.
*2 In case of using FHV-321 and FHM-211
*PhotoMOS relay type is also available.

External dimension

External dimension

External dimension

prv 10 ed1

External dimension

prv 10 ed2

I/O circuit

I/O Circuit

Projector

lav setuzoku toukou

Light-projecting amount lowering output

Operating modeNOMALABNOMAL
Pin No. of connector5-69-1010-115-69-1010-11
Power-OFF stateOFFOPENCLOSEOFFOPENCLOSE
Power-ON stateWhen normalONCLOSEOPENOFFOPENCLOSE
When troubledOFFOPENCLOSEONCLOSEOPEN

Receiver

lav setuzoku jukou

Control output(Changeover by inner switch)

Operating modeLight-ONDark-ON
Pin No. of connector5-69-1010-115-69-1010-11
Power-OFF stateOFFOPENCLOSEOFFOPENCLOSE
Power-ON stateWhen light-enteringONCLOSEOPENOFFOPENCLOSE
When light-interruptingOFFOPENCLOSEONCLOSEOPEN

Warning output

Pin No. of connector.7-812-1313-14
Power-OFF stateOFFOPENCLOSE
Power-ON stateWhen normalONCLOSEOPEN
When troubledOFFOPENCLOSE

Characteristics Data

Characteristics Data

Projector/receiver LAV-10P/LAV-10A

lav tokusei10

Projector/receiver LAV-11P/LAV-10A

lav tokusei11

Sản phẩm tương tự